| YAHOOKA - YAHOOKA -> How to make a bubbler | Start A New Topic | Reply |
| Post Info | TOPIC: How to make a bubbler |
| Posted By: {orange kush} Posted On: Apr 22, 2005 Views: 2682 | How to make a bubbler Does any one know how to make a good cheap bubbler that will last a while. I can't think of a way. let me know what you think. |
| Posted By: Bert Posted On: Apr 26, 2005 Views: 2642 | RE: How to make a bubbler Materials: 1 gatorade bottle, 1 tube(empty pen), aluminum, tape. Steps: 1) Make a hole in the gatorade bottle in the middle that fits the empty pin perfectly. Put the pen in slanted to where the other side of pen is near bottom of bottle. 2)Tape so it is airtight. Then make another hole on the side as your "carb". 3) Make a bowl w/ the aluminum however u want. Put the bowl at the end of the pen and tape airtight. 4)The part of the bottle where you drink, will be where u hit the weed. 5) Put water in it and blaze on!! |
| Posted By: mcguyver Posted On: Apr 29, 2005 Views: 2619 | RE: How to make a bubbler you learn to make those in pot smoking 101, have some balls buy a real bong, acrylic ones are real cheap. happy smoking |
| Posted By: AL Posted On: May 2, 2005 Views: 2586 | RE: How to make a bubbler what you need: plastic drink bottle 6" piece of hose-pipe lighter foil how to: 1. burn a hole about 1/3 from the bottom and while the plastic is wet and sticky place the hosepipe in quickly, this will form an airtight seal. 2. burn a hole about 1" or 2" from the top on the opposite side to the other, this hole should be about the size of your thumb(this is the shotty: used to clear air between tokes) 3. wrap some foil around the end of the hosepipe so there is a slight dip 4. peirce small holes in the foil (voila filter) |
| Posted By: Bonglore Posted On: May 5, 2005 Views: 2551 | RE: How to make a bubbler What you need: 6 feet of 4" PVC piping one ending for the pvc 1 small water pump (water fountains in hardware stores) some variety of gallon sized sealable plastic container a tube o' caulk epoxy 1 hot plate 1 pot holder a small vacuum pump one foot 1/2" copper tubing steel stem of some variety ~1/2" in diameter about two feet of clear plastic tubing about the same diameter as the copper tubing some variety of bowl (look around the bolts in a hardware store you'd be amazed at what you can find a saw dremmel tool (preferable) or drill duct tape How to make: 1. Take 6 feet pvc and attach end to one side. This is the bottom of you bubbler. You will smoke out of the top. 2. Drill 1/2" hole at a 45 degree angle about 6 inches from bottom of pvc. 3. Insert Clear plastic tubing into hole in pvc so that it touches bottom. 4. Cut the rest of the clear plastic tubing so that each piece is about a foot long. 5. Attach plastic tubing connected to pvc to the water pump exit. 6. Attach free piece of plastic tubing to water pump input. 7. Attach the other end of this to the top of the gallon plastic container by drilling a hole and inserting it. 8. Drill hole about 4 inches from bottom of plastic container and insert copper tubing. 9. Attach this to the exit of the vacuum pump. 10. Attach the other part of the vacuum pump to the steel tube and attach that to the bowl. 11. Place the pot holder under the plastic container and the hot plate under that. 12. Epoxy and then caulk all joints. Duct tape any loose seals if you cant epoxy or caulk. 13. Put warm water in the plastic container and turn on the hot plate (hot water cleans the smoke better). 14. Fill the PVC pipe with ice water about a foot up. 15. Turn on vacuum and water pumps. 16. Fill up bowl and have a rip. This thing is essentially a THC syringe. (Oh and use a butane torch light, the vacuum will probably put out a bic) |
| Posted By: jimbodad Posted On: May 5, 2005 Views: 2543 | RE: How to make a bubbler I made one pretty simply, and its lasted a while its pretty portable and you dont even need to fill it with water if you dont have any all you need is a: paperclip holder or simular small plastic container with a lid and a wide opening, simular to this: a pen tube a straw or another pen tube for the mouth piece a metal botel cap (the reusable kinds youll find on some sodas like perrier or vinegar or olive oil containers) air tight tape, (i used electrical) all you do is take the lid of your small plastic container and begin to seal it off with tape. when it is about half coverd, place the pen tube and mouth piece (what ever you decide to use) next to each other, then finish taping the other half. Remember, your going to want to leave enough room for a bowl, and dont want the pen length longer than the chamber. make sure you keep the straw towards the top you want the maximum distance between the pen tube and your mouth piece in the chamber. once you finish taping off the lid with both the pen tube and the straw/mouth piece, poke some holes through your bottle cap and fasten to the end of the pen tube. remeber, keep the holes concentrated in a small group that way they all fit over the pen tube opening. tape on your bowl and finish making everything air tight. fill with watter, add some bud, and light up for pictures email me at aflyinglobster@hotmail.com |
| Posted By: Guest Posted On: May 17, 2005 Views: 2423 | RE: How to make a bubbler I prefer what we Germans call "Eimer", that means Bucket, it is a normal Plastic Bottle, where you cut away the Bottom. On the top, where you drink, you put a Aluminiumbowl, you don't need a chillum. Fill in the Pot, and go to a Lake, or a pond, Hold the "Eimer" in the Water, and burn the Pot, through soft shaking, the Smoke of one Joint gets into the bottle, then pull away the bows, and suck the smoke into your lungs! |
| Posted By: Jake Posted On: Sep 10, 2005 Views: 1915 | RE: How to make a bubbler That makes absolutely no sense you German bastard. |
| Posted By: quinny Posted On: Dec 24, 2005 Views: 1573 | RE: How to make a bubbler hahahahahhahahaha YES! |